İçeriğe geç

Connecting and configuring a scanner in IZI

Опубликовано: · Обновлено: (1 месяц назад)· IZI Team

Bu içerik henüz dilinizde mevcut değil.

Connecting and configuring a scanner in IZI

Section titled “Connecting and configuring a scanner in IZI”

Scanning is available to all clubs without activation by Support. You need permission for the operation, products with barcodes in the catalog and a suitable scanner. Marked goods also require a configured cashbox and marking validation.

The barcode type and the way data reaches the PC are separate settings. A 2D scanner usually reads both linear barcodes and Data Matrix: one device can serve both purposes.

Type or input modeSettings
Linear 1D scannerUSB HID Keyboard; enable the EAN-8/EAN-13 and Code128 formats you use; Enter suffix, or Tab; no arbitrary prefix, truncation or character replacement
2D scanner for marked goodsUSB HID Keyboard; enable Data Matrix and GS1 DataMatrix; preserve letter case, punctuation and GS; Enter or Tab suffix
Alt/keypad emulation or text injectionOriginal ASCII text including GS; verify the complete code in CRM. A working mode need not change just because the PC uses RU
COM/Serial, USB CDCCRM does not read COM directly. Use a supported keyboard mode or existing keyboard wedge software

Connect the device and configure the terminator

Section titled “Connect the device and configure the terminator”
  1. Connect the scanner to USB. HID mode identifies it as a keyboard and normally needs no separate driver.
  2. Select USB HID Keyboard using your model’s manual.
  3. Enable Enter after each code, also called Add CR or Suffix: CR. CRM also accepts Tab.
  4. Disable arbitrary prefixes, truncation, character replacement and forced case conversion.

CRM has no scanner connection selector or COM port settings. Configure the device using its manual or vendor software. Do not scan programming barcodes intended for another model.

Use a 2D scanner supporting GS1 DataMatrix. Disable case conversion, truncation and character replacement. Marking codes identify individual packages: preserve uppercase and lowercase letters, punctuation and invisible separators.

FNC1 separates variable-length fields in GS1 DataMatrix. In transmitted text the separator is GS, ASCII 29, hex 1D. This differs from Enter, Tab and literal text such as <GS> or \u001d. GS1 guideline.

The marking dialog accepts the GS character itself, Ctrl+], or an unmodified F8 key. Select the appropriate control-character mode using the scanner manual. Do not replace GS with spaces, Enter or printed text.

CRM recognizes a leading ]d2 AIM identifier on GS1 DataMatrix; arbitrary prefixes are unnecessary. It can recover some missing separators or keyboard characters only when the cashbox confirms one unique candidate. This does not replace transmitting the complete original code.

For ordinary USB HID keystrokes the recommended starting scanner profile is US / United States keyboard. This is a device setting. The operator does not need to change the PC layout before every scan.

Scanner optionMeaning and check
Keyboard CountryDetermines the keys sent for each character; start with US for ordinary HID
Caps Lock Override / Ignore Caps LockHelps preserve case with Caps Lock enabled; names and behavior vary by model
Convert CasePreserve original case; disable forced uppercase or lowercase
Keypad / Alt emulationAnother transmission mode; keep a working mode that already preserves the complete code and GS

Do not enable all options as a universal recipe. Follow manufacturer instructions, such as the separate parameters in the Zebra documentation.

Verify an ordinary barcode and a marking code

Section titled “Verify an ordinary barcode and a marking code”
  1. Scan an ordinary barcode in a text editor; check the complete value and terminator.
  2. Open New order in CRM and scan a product barcode registered in the catalog. Check the selected product.
  3. For marked goods, wait for the marking dialog and scan the Data Matrix on that individual package.
  4. Check the cashbox result. If Caps Lock behavior makes the original case ambiguous, CRM submits the actual input text to the cashbox. If recognition fails, scan again; contact support if the error persists.
  5. Repeat with RU and EN, then Caps Lock off and on. The browser cannot always distinguish Caps Lock compensation modes, so recovery of the original case is not guaranteed for both modes. If results differ, check the device profile against its manual.
  6. As part of cashbox acceptance, perform an agreed sale and check the receipt.

A text editor only verifies text arrival. It may not display GS and does not establish cryptographic validation, marking-service availability or permission to sell.

The 6–64 characters without spaces restriction applies to ordinary product barcodes in the IZI catalog. Do not truncate marking codes to this length.

Use one 2D scanner for both code types, or connect two devices. CRM has no scanner-type switch:

  1. Scan a product barcode in product search or a warehouse page.
  2. While the marking dialog is open, it owns the scan. The code must not add another product or open another order.
  3. After closing the dialog, scan the next product barcode.

Scan sequentially. Browsers receive HID scanner input as a keyboard stream and cannot reliably separate two devices scanning simultaneously.

SymptomCheck
No input even in a text editorUSB, power, HID mode and enabled symbologies
Product not foundComplete barcode in the product card, selected club and unwanted prefixes
Code appears but validation does not startEnter/Tab suffix; the marking dialog also has a validation button
Missing characters or changed caseKeyboard Country, Convert Case, Caps Lock Override and truncation
Marking recovery is ambiguousScan again, verify GS and punctuation, or paste the complete original code
Scanning triggers a browser commandControl-character mapping; transmit GS using a supported mode inside the marking dialog
Cashbox unavailableKkmServer on the cashbox PC and an active device
Cashbox prohibits saleExact marking response, package state and permit-regime settings; repairing input does not override a prohibition

A scanner that irreversibly truncates data or changes case before transmission loses information. Correct its device profile. For Support, include the model, connection mode, keyboard profile, Caps Lock state, exact error and validation time.

Sık sorulan sorular

Does Support need to enable scanning?

No. Scanning is available to all clubs. Staff need permission for the sale or warehouse operation.

Must the PC keyboard be switched to English?

No switch between RU and EN is required before every scan. Configure the scanner's keyboard country and data conversion using its model-specific manual.

Can a standard scanner read Data Matrix?

Marking requires a 2D scanner supporting Data Matrix and GS1 DataMatrix. A linear 1D scanner cannot read these symbols.

Can I connect a COM scanner?

CRM does not read COM directly. Select USB HID Keyboard if supported, or use existing software that delivers the scanner's data as keyboard input.

About IZI